GHOST 52/60" MOUNT ASSEMBLY KIT

360 HEAD ASSEMBLY V.1.1

FLUSH MOUNT KIT: ELITE FS 9

FLUSH MOUNT KIT: ELITE FS 7

SUNCOVER: ELITE-7 FS

CNR CLIP KIT: ELITE-7+9 FS

The Prop Shaft Anode for the Lowrance Ghost® trolling motor allows for use in brackish water without voiding the Lowrance Ghost trolling motor warranty. The Prop Shaft Anode is a ring-shaped fitting that is installed over the existing propeller nut, on th

ELITE FS 7 with No Transducer (ROW) The new Elite™ Fishing System (FS) gives you access to the full line-up of Lowrance fishfinding tools – including ActiveTarget™ live sonar, Active Imaging™, FishReveal™ and preloaded C-MAP® Contour™ + charts – all at a

ELITE FS 7 with xSonic HDI M/H 455/800 Transducer (ROW) The new Elite™ Fishing System (FS) gives you access to the full line-up of Lowrance fishfinding tools – including ActiveTarget™ live sonar, Active Imaging™, FishReveal™ and preloaded C-MAP® Contour™

ELITE FS 9 with Active Imaging 3-in-1 Transducer (ROW) The new Elite™ Fishing System (FS) gives you access to the full line-up of Lowrance fishfinding tools – including ActiveTarget™ live sonar, Active Imaging™, FishReveal™ and preloaded C-MAP® Contour™

Side plate kit, GHOST 52”/GHOST 60”: 1x Cover mount RH, GHOST 52”/GHOST 60” 1x Cover mount LH, GHOST 52”/GHOST 60” 6x Screw, SHCS M4 x 0.7 x14, SS

Lower extrusion kit, GHOST 52”/GHOST 60”:1x Lower extrusion, with bushing, , GHOST 52”/GHOST 60”

Wear bearing kit, GHOST 52”/GHOST 60”: 2x Wear bearing, GHOST 52”/GHOST 60”

Lift assist kit, GHOST 52”/GHOST 60”: 1x Gas spring, compression/traction, GHOST 52”/60”, 2x Binding barrel, 5/16 x 1”, Pan, PH, SS, 2x Screw, 1/4-20 x 5/16”, Pan, PH, SS

Latch trigger, GHOST 52”/GHOST 60” 2x Latch trigger, GHOST 52”/GHOST 60”

Pushrod kit, GHOST 52”/GHOST 60”: 1x Clevis bracket, 4x Screw, M5x8mm, hex, button, SS, 1x Pushrod, finish machine with bushing, GHOST 52”/GHOST 60”

2x Nose cone O-ring, 1x Cable tie/heat shrink kit (not shown in the illustration), 1x Column, inner, GHOST 52”/lower unit (pre-assembled)

1x Cable, head to pedal, GHOST GHOST 52”, 2x Screw, M3 x 10, torx, 1x Seal, strain relief, 1x Cable tie/heat shrink kit, 1x PCBA thermal pad

1x Cable, head to pedal, GHOST 52”, 2x Screw, M3 x 10, torx, 1x Seal, strain relief, 1x Cable tie/heat shrink kit, 1x PCBA thermal pad

1x Lower housing assy with outer column, GHOST 60”, 1x Cable tie/heat shrink kit (not shown in the illustration), 2x Screw, M3 x 10, torx, 1x PCBA thermal pad

1x Lower housing assy with outer column, GHOST 52”, 1x Cable tie/heat shrink kit (not shown in the illustration), 2x Screw, M3 x 10, torx, 1x PCBA thermal pad

HDI Skimmer® transducer 83/200/455/800kHz for Hook2* and Hook Reveal, with built in temp. Includes mounting bracket and hardware. Cable Length 6m (20 ft). Connector: 8 pin push fit. (*83 kHz / Mid CHIRP frequency options are not available on Hook2)

HDI Skimmer® transducer 50/200/455/800kHz for Hook2* and Hook Reveal, with built in temp. Includes mounting bracket and hardware. Cable Length 6m (20 ft). Connector: 8 pin push fit. (* 50 kHz / Low CHIRP frequency options are not available on Hook2)

GHOST 47" MOUNT ASSEMBLY KIT